Balance polishing with downstream protection. Compare material families, documented retention and operating requirements.
Request a configuration review
A 0.45 micron pleated filter cartridge is a fine particle-polishing option for compatible liquids and for selected stages ahead of finer filtration. Media choice determines wetting, chemical compatibility and product-contact considerations; the micron number does not identify these properties.
For a process with visible clarity or particle-count requirements, define the measurable acceptance criterion before choosing PP, PES, PVDF, nylon or PTFE. A clear-looking filtrate is not evidence of a particular particle-retention efficiency or microbiological quality.
Before a qualified final membrane, assess whether a 0.45 µm prefilter removes the fraction responsible for fouling without adding unnecessary pressure drop. Compare real operating throughput rather than assuming that the closest numerical prefilter always offers the best protection.
This is a cross-material selection guide. The linked family pages are the catalog references, not substitutes for a confirmed grade-specific data sheet. Listed family information does not establish that every combination of dimensions, seals and rating is available.
| Material / request | Catalog status | Selection question |
|---|---|---|
| PP | Exact 0.45 µm grade listed on the detailed family page | Polypropylene; evaluate for compatible water and process liquids. |
| PES | Exact 0.45 µm grade listed on the detailed family page | Polyethersulfone membrane; evaluate wetting and product-contact requirements. |
| PTFE | Exact 0.45 µm grade listed on the detailed family page | Confirm hydrophilic or hydrophobic configuration and complete fluid compatibility. |
| Nylon | Exact 0.45 µm grade listed on the detailed family page | Confirm the exact nylon grade and compatibility of the full cartridge. |
| PVDF | Exact 0.45 µm grade listed on the detailed family page | Polyvinylidene fluoride membrane; confirm the selected grade and operating envelope. |
For the existing polypropylene-specific product guide, see 0.45 micron PP pleated filter cartridge. That page addresses the PP construction; this page compares material and process-selection choices.
Use 0.45 µm where its documented retention meets the polishing or prefiltration duty. Evaluate 0.22 µm when the finer requirement is justified. Do not assume an exact change in flow or service life from the rating ratio.
Nearby selection guides: 0.22 µm · 0.65 µm. Compare equivalent efficiency definitions and cartridge dimensions before changing grade.
| Required rating | 0.45 µm; state nominal/absolute definition and required retention efficiency. |
|---|---|
| Availability | Listed material families above; confirm the exact orderable combination. |
| Dimensions and interface | Confirm actual length, OD, ID, end-cap drawing and gasket arrangement against the existing housing. |
| Fluid and hydraulics | Provide fluid composition, concentration, viscosity at temperature, flow and allowable clean differential pressure. |
| Operating limits | Obtain configuration-specific temperature, pressure and change-out limits. Limits cannot be inferred from the micron number. |
| Documents | Request a grade-specific data sheet, retention method and any product-contact or validation records required for the application. |
Record feed turbidity or particle counts, clean differential pressure, throughput and filtrate quality during a trial. Request product-contact documentation where the application requires it and confirm the complete cartridge is compatible with cleaning conditions.
No grade-specific flow rate, retention percentage, service life, certification or microbial-validation result is asserted by this guide. Those values must come from documentation for the ordered configuration.
A 0.45 micron pleated filter cartridge is a fine particle-polishing option for compatible liquids and for selected stages ahead of finer filtration. Media choice determines wetting, chemical compatibility and product-contact considerations; the micron number does not identify these properties.
Use 0.45 µm where its documented retention meets the polishing or prefiltration duty. Evaluate 0.22 µm when the finer requirement is justified. Do not assume an exact change in flow or service life from the rating ratio.
The number alone does not say. Request the retention efficiency, challenge conditions and test method for the exact grade. Do not assume a universal efficiency percentage from the word nominal or absolute.
Match the actual overall length, outside and inside diameters, end-cap interface and seal arrangement against the housing drawing. A matching micron rating or nominal length does not establish fit.
No. Particle-rating information alone does not establish sterilizing performance or removal of dissolved salts and chemicals. Microbial claims need product-specific evidence and process validation; dissolved contaminants require an appropriate treatment process.
Send the required rating and efficiency, liquid and concentration, flow, viscosity, temperature, pressure, particle load, cartridge dimensions, end-cap drawing, seals, quantity and required documentation. Ask INCE filtration to confirm the exact configuration before purchase.
Prepared by INCE filtration from the linked material-family catalog information. Reviewed: 30 October 2026. Availability statements describe the published family lists at preparation time; a written quotation and data sheet establish the supplied configuration.
PP family · PES family · PTFE family · Nylon family · PVDF family
All pleated filter cartridges · Request a configuration review
WhatsApp