Compare fine membrane and PP media. Compare material families, documented retention and operating requirements.
Request a configuration review
A 0.1 micron pleated filter cartridge is a fine particle-control option for compatible process liquids. Choosing the media and its documented retention performance matters as much as the 0.1 µm label. This page compares the material families rather than treating every 0.1 micron cartridge as interchangeable.
For a clean aqueous stream, evaluate PES or PVDF membrane configurations alongside PP according to the particle specification, wetting requirements and extractables limits. For solvent service, evaluate the complete PTFE configuration against the solvent and temperature; the membrane name alone does not establish compatibility.
When a fine cartridge blocks rapidly, measure the incoming particle distribution and evaluate an upstream stage. Increasing the final rating merely to extend run time can compromise the required particle control; increasing effective area may be the more appropriate change.
This is a cross-material selection guide. The linked family pages are the catalog references, not substitutes for a confirmed grade-specific data sheet. Listed family information does not establish that every combination of dimensions, seals and rating is available.
| Material / request | Catalog status | Selection question |
|---|---|---|
| PP | Exact 0.1 µm grade listed on the detailed family page | Polypropylene; evaluate for compatible water and process liquids. |
| PES | Exact 0.1 µm grade listed on the detailed family page | Polyethersulfone membrane; evaluate wetting and product-contact requirements. |
| PTFE | Exact 0.1 µm grade listed on the detailed family page | Confirm hydrophilic or hydrophobic configuration and complete fluid compatibility. |
| Nylon | Exact 0.1 µm grade listed on the detailed family page | Confirm the exact nylon grade and compatibility of the full cartridge. |
| PVDF | Exact 0.1 µm grade listed on the detailed family page | Polyvinylidene fluoride membrane; confirm the selected grade and operating envelope. |
For the existing polypropylene-specific product guide, see 0.1 micron PP pleated filter cartridge. That page addresses the PP construction; this page compares material and process-selection choices.
0.1 µm is the finer stated rating. Select it when the process particle target justifies that grade and its tested retention meets the requirement. Neither number alone proves virus removal, mycoplasma removal or sterile output.
Nearby selection guides: 0.22 µm. Compare equivalent efficiency definitions and cartridge dimensions before changing grade.
| Required rating | 0.1 µm; state nominal/absolute definition and required retention efficiency. |
|---|---|
| Availability | Listed material families above; confirm the exact orderable combination. |
| Dimensions and interface | Confirm actual length, OD, ID, end-cap drawing and gasket arrangement against the existing housing. |
| Fluid and hydraulics | Provide fluid composition, concentration, viscosity at temperature, flow and allowable clean differential pressure. |
| Operating limits | Obtain configuration-specific temperature, pressure and change-out limits. Limits cannot be inferred from the micron number. |
| Documents | Request a grade-specific data sheet, retention method and any product-contact or validation records required for the application. |
Request retention efficiency at the target particle size, the exact test method, the clean flow-versus-pressure curve and extractables information where relevant. For sensitive liquids, assess product adsorption and recovery with the chosen media.
No grade-specific flow rate, retention percentage, service life, certification or microbial-validation result is asserted by this guide. Those values must come from documentation for the ordered configuration.
A 0.1 micron pleated filter cartridge is a fine particle-control option for compatible process liquids. Choosing the media and its documented retention performance matters as much as the 0.1 µm label. This page compares the material families rather than treating every 0.1 micron cartridge as interchangeable.
0.1 µm is the finer stated rating. Select it when the process particle target justifies that grade and its tested retention meets the requirement. Neither number alone proves virus removal, mycoplasma removal or sterile output.
The number alone does not say. Request the retention efficiency, challenge conditions and test method for the exact grade. Do not assume a universal efficiency percentage from the word nominal or absolute.
Match the actual overall length, outside and inside diameters, end-cap interface and seal arrangement against the housing drawing. A matching micron rating or nominal length does not establish fit.
No. Particle-rating information alone does not establish sterilizing performance or removal of dissolved salts and chemicals. Microbial claims need product-specific evidence and process validation; dissolved contaminants require an appropriate treatment process.
Send the required rating and efficiency, liquid and concentration, flow, viscosity, temperature, pressure, particle load, cartridge dimensions, end-cap drawing, seals, quantity and required documentation. Ask INCE filtration to confirm the exact configuration before purchase.
Prepared by INCE filtration from the linked material-family catalog information. Reviewed: 30 October 2026. Availability statements describe the published family lists at preparation time; a written quotation and data sheet establish the supplied configuration.
PP family · PES family · PTFE family · Nylon family · PVDF family
All pleated filter cartridges · Request a configuration review
WhatsApp