Measure particle load and viscosity together. Compare material families, documented retention and operating requirements.
Request a configuration review
A 10 micron pleated filter cartridge is a general process-filtration grade for removal of suspended particles from compatible liquids. PP and glass fiber are listed material families at 10 µm; selecting between them requires operating and retention data.
For a coating, chemical or other viscous liquid, provide viscosity at operating temperature rather than only naming the fluid. Water flow data should not be treated as a direct throughput guarantee for the process liquid, and seal compatibility must be checked separately.
For general equipment protection, identify the smallest particle sizes that cause the actual problem. If fouling is driven by a finer fraction, changing from 20 to 10 µm may still be insufficient; if solids loading is high, assess upstream separation as well as cartridge area.
This is a cross-material selection guide. The linked family pages are the catalog references, not substitutes for a confirmed grade-specific data sheet. Listed family information does not establish that every combination of dimensions, seals and rating is available.
| Material / request | Catalog status | Selection question |
|---|---|---|
| PP | Exact 10 µm grade listed on the detailed family page | Polypropylene; evaluate for compatible water and process liquids. |
| Glass Fiber | Exact 10 µm grade listed on the detailed family page | Confirm the multilayer media, support construction and approved operating conditions. |
For the existing polypropylene-specific product guide, see 10 micron PP pleated filter cartridge. That page addresses the PP construction; this page compares material and process-selection choices.
10 µm states the finer target. Compare downstream particle results and total operating pressure drop for the chosen construction. Neither label specifies an identical dirt capacity across suppliers or media families.
Nearby selection guides: 5 µm · 20 µm. Compare equivalent efficiency definitions and cartridge dimensions before changing grade.
| Required rating | 10 µm; state nominal/absolute definition and required retention efficiency. |
|---|---|
| Availability | Listed material families above; confirm the exact orderable combination. |
| Dimensions and interface | Confirm actual length, OD, ID, end-cap drawing and gasket arrangement against the existing housing. |
| Fluid and hydraulics | Provide fluid composition, concentration, viscosity at temperature, flow and allowable clean differential pressure. |
| Operating limits | Obtain configuration-specific temperature, pressure and change-out limits. Limits cannot be inferred from the micron number. |
| Documents | Request a grade-specific data sheet, retention method and any product-contact or validation records required for the application. |
Supply liquid concentration, operating viscosity, temperature, design flow and particle-count information. Ask for documented performance at the chosen construction and a trial plan with a defined quality endpoint and change-out criterion.
No grade-specific flow rate, retention percentage, service life, certification or microbial-validation result is asserted by this guide. Those values must come from documentation for the ordered configuration.
A 10 micron pleated filter cartridge is a general process-filtration grade for removal of suspended particles from compatible liquids. PP and glass fiber are listed material families at 10 µm; selecting between them requires operating and retention data.
10 µm states the finer target. Compare downstream particle results and total operating pressure drop for the chosen construction. Neither label specifies an identical dirt capacity across suppliers or media families.
The number alone does not say. Request the retention efficiency, challenge conditions and test method for the exact grade. Do not assume a universal efficiency percentage from the word nominal or absolute.
Match the actual overall length, outside and inside diameters, end-cap interface and seal arrangement against the housing drawing. A matching micron rating or nominal length does not establish fit.
No. Particle-rating information alone does not establish sterilizing performance or removal of dissolved salts and chemicals. Microbial claims need product-specific evidence and process validation; dissolved contaminants require an appropriate treatment process.
Send the required rating and efficiency, liquid and concentration, flow, viscosity, temperature, pressure, particle load, cartridge dimensions, end-cap drawing, seals, quantity and required documentation. Ask INCE filtration to confirm the exact configuration before purchase.
Prepared by INCE filtration from the linked material-family catalog information. Reviewed: 30 October 2026. Availability statements describe the published family lists at preparation time; a written quotation and data sheet establish the supplied configuration.
PP family · Glass Fiber family
All pleated filter cartridges · Request a configuration review
WhatsApp