Compare PP and glass fiber constructions. Compare material families, documented retention and operating requirements.
Request a configuration review
A 50 micron pleated filter cartridge is a coarse particle-control option listed in the INCE PP and glass fiber families. It is intended for evaluating larger suspended-particle removal, with final selection based on documented efficiency and the downstream requirement.
Where chemical compatibility favors PP, confirm the complete configuration and operating temperature. Where a glass fiber candidate is proposed for a loaded stream, ask for evidence relevant to the real fluid and solids rather than assuming one media always has longer life.
For an installation before finer cartridges, compare the total filter train. A coarse cartridge that lets the dominant fouling fraction pass may add cost without extending the downstream run; measure stage-by-stage pressure and throughput.
This is a cross-material selection guide. The linked family pages are the catalog references, not substitutes for a confirmed grade-specific data sheet. Listed family information does not establish that every combination of dimensions, seals and rating is available.
| Material / request | Catalog status | Selection question |
|---|---|---|
| PP | Exact 50 µm grade listed on the detailed family page | Polypropylene; evaluate for compatible water and process liquids. |
| Glass Fiber | Exact 50 µm grade listed on the detailed family page | Confirm the multilayer media, support construction and approved operating conditions. |
For the existing polypropylene-specific product guide, see 50 micron PP pleated filter cartridge. That page addresses the PP construction; this page compares material and process-selection choices.
50 µm is the finer stated rating and is available in listed PP and glass fiber series. The detailed 70 µm option belongs to the glass fiber family in this guide. A switch between these grades may also change the material, so compare both factors.
Nearby selection guides: 40 µm · 70 µm. Compare equivalent efficiency definitions and cartridge dimensions before changing grade.
| Required rating | 50 µm; state nominal/absolute definition and required retention efficiency. |
|---|---|
| Availability | Listed material families above; confirm the exact orderable combination. |
| Dimensions and interface | Confirm actual length, OD, ID, end-cap drawing and gasket arrangement against the existing housing. |
| Fluid and hydraulics | Provide fluid composition, concentration, viscosity at temperature, flow and allowable clean differential pressure. |
| Operating limits | Obtain configuration-specific temperature, pressure and change-out limits. Limits cannot be inferred from the micron number. |
| Documents | Request a grade-specific data sheet, retention method and any product-contact or validation records required for the application. |
Confirm the required retained particle fraction, upstream loading and acceptable pressure drop. Ask for media area, retention evidence and fit details, including actual length, end-cap type and gasket material.
No grade-specific flow rate, retention percentage, service life, certification or microbial-validation result is asserted by this guide. Those values must come from documentation for the ordered configuration.
A 50 micron pleated filter cartridge is a coarse particle-control option listed in the INCE PP and glass fiber families. It is intended for evaluating larger suspended-particle removal, with final selection based on documented efficiency and the downstream requirement.
50 µm is the finer stated rating and is available in listed PP and glass fiber series. The detailed 70 µm option belongs to the glass fiber family in this guide. A switch between these grades may also change the material, so compare both factors.
The number alone does not say. Request the retention efficiency, challenge conditions and test method for the exact grade. Do not assume a universal efficiency percentage from the word nominal or absolute.
Match the actual overall length, outside and inside diameters, end-cap interface and seal arrangement against the housing drawing. A matching micron rating or nominal length does not establish fit.
No. Particle-rating information alone does not establish sterilizing performance or removal of dissolved salts and chemicals. Microbial claims need product-specific evidence and process validation; dissolved contaminants require an appropriate treatment process.
Send the required rating and efficiency, liquid and concentration, flow, viscosity, temperature, pressure, particle load, cartridge dimensions, end-cap drawing, seals, quantity and required documentation. Ask INCE filtration to confirm the exact configuration before purchase.
Prepared by INCE filtration from the linked material-family catalog information. Reviewed: 30 October 2026. Availability statements describe the published family lists at preparation time; a written quotation and data sheet establish the supplied configuration.
PP family · Glass Fiber family
All pleated filter cartridges · Request a configuration review
WhatsApp