Industrial Filter Bags · Filter Cartridges · Filter Housings · Filter Mesh Manufacturer & Custom Supplier Replacement style · OEM size · Custom micron rating · Industrial filtration supply

What Control Logic Should Buyers Specify for a Self-Cleaning Scraper Filter?

Prepare a self-cleaning scraper filter RFQ covering timed, differential-pressure and external-signal cleaning, HMI, alarms, drain logic, motor data and process interlocks.

Short answer: specify the scraper filter as a controlled process package, not only as a stainless-steel vessel. The RFQ should define cleaning triggers, differential-pressure instruments, timer ranges, external signals, drain-valve sequence, motor power supply, alarms, local/remote modes and the safe state after power or signal loss.

Request a Self-Cleaning Filter Proposal

The INCE self-cleaning product sheet lists PLC/HMI control with cleaning triggered by time, differential pressure or external process signals. It also lists a motorized scraper, automatic drain, reusable 304/316L V-slot screen and a DN40 flanged drain. Final logic must be agreed for the actual liquid and plant control system.

INCE self-cleaning scraper filter housing package
Site-owned INCE self-cleaning filter image. The quotation should define the complete vessel, drive, screen, drain and control package.

Which cleaning trigger should the RFQ include?

Trigger Use in the control narrative Buyer should define
Elapsed time Runs a cleaning cycle at an adjustable interval Initial interval, adjustable range and override conditions
Differential pressure Starts cleaning when measured ΔP reaches the agreed setpoint Transmitter range, units, alarm and high-high response
External signal Accepts a plant PLC or process permission/start signal Signal type, voltage, dry contact or communications requirement
Manual command Allows a supervised local test or maintenance cycle Key/selector access, hold-to-run logic and interlocks

A robust RFQ normally requests at least one primary trigger plus a backup timed cycle, but the final sequence should match the contamination rate and plant philosophy. Review the verified product range at the self-cleaning filter housing page.

What verified mechanical data must be linked to the controls?

  • Reference housing sizes: 219, 273, 325, 377, 400, 450, 550 and 800 mm.
  • Reference flow: at least 1 T/H, with final design based on the required process flow.
  • Filtration rating: up to 20 µm; confirm the actual V-slot opening and retention requirement.
  • Filter area: at least 0.12 m², customizable.
  • Housing/screen: 304 or 316L stainless steel V-slot element.
  • Reference scraper/seal: PTFE scraper and Viton/FKM seal.
  • Operating pressure: 0.8 MPa reference, subject to final design confirmation.
  • Reference drive power: 0.37–0.55 kW; final motor depends on torque and unit size.
Internal and external scraper filter configuration reference
Site-owned INCE product image. Select internal or external scraping from deposit location, filtration direction and contaminant behavior.

Control-panel and integration checklist

System item RFQ requirement
Power Voltage, phase, frequency, motor starter/VFD requirement and control voltage
HMI Language, user levels, setpoint access, cycle counter and alarm history
Signals Run, ready, cleaning, fault, high ΔP, drain open/closed and remote enable
Communications Required protocol, network medium and register/point list
Drain sequence Valve type, open time, confirmation switch, receiving system and discharge restrictions
Interlocks No-flow, valve position, motor overload, high pressure, maintenance mode and emergency stop
Environment Indoor/outdoor, enclosure rating, ambient temperature and hazardous-area requirement
Documentation GA drawing, P&ID, I/O list, wiring diagram, control narrative, manuals and test records

Send Your P&ID and Control Requirements

What process data is still required?

Send the liquid composition, viscosity at operating temperature, solids concentration, particle shape, required flow, operating/design pressure, temperature, target slot size, allowable ΔP, inlet/outlet standard, installation orientation and discharge destination. The controller cannot compensate for a screen that is undersized for viscous liquid or a drain line that cannot accept the discharged solids.

Fully automatic INCE self-cleaning filter package
Site-owned INCE automatic-filter image. Confirm panel, instruments and valve scope explicitly; do not assume every accessory is included.

Factory acceptance and commissioning questions

  • Will the supplier demonstrate timed, ΔP and remote-start cycles?
  • Are simulated instrument failures and motor overload alarms included in FAT?
  • Is the drain valve supplied, and is position feedback included?
  • Which parameters are adjustable without engineering access?
  • Who supplies field instruments, cabling and plant PLC integration?
  • What spare scraper, seal and screen items should be quoted?

Frequently asked questions

Can cleaning run without stopping filtration?

The product is designed for on-line automatic cleaning, but the allowable flow and pressure disturbance must be confirmed for the engineered package.

Should cleaning be time-based or differential-pressure-based?

Use the process behavior to choose. Many buyers request ΔP control with a backup timer and external command, subject to the agreed control narrative.

What should be included for an accurate quotation?

Provide process data, screen target, mechanical connections, power, I/O, communications, interlocks, drain sequence, drawings, documents and quantity.

Get an Engineered Control and Housing Quote

Related Articles

Continue Reading About Liquid Filtration

Need a Filter Bag Recommendation?

Send the liquid, micron target, flow, pressure, temperature, bag dimensions and quantity for review.

Start a Filter Bag Inquiry
Filtration Engineer
● Online
×
WhatsApp