Industrial Filter Bags · Filter Cartridges · Filter Housings · Filter Mesh Manufacturer & Custom Supplier Replacement style · OEM size · Custom micron rating · Industrial filtration supply

Nylon or Polyester Filter Mesh Disc: What Should OEM Buyers Specify?

Choose nylon or polyester filter mesh discs by parent mesh, aperture, OD, ID, layers, edge finish, liquid, cleaning method and OEM drawing requirements.

custom fabricated filter mesh parts for industrial filtration

Short answer: choose nylon when a flexible monofilament disc suits the assembly, and choose polyester when dimensional stability is the stronger purchasing requirement. Do not decide from polymer name alone: confirm the parent mesh, aperture, thread diameter, finished OD/ID, edge condition, layers, liquid, temperature, differential pressure and cleaning method.

Send Your Mesh Disc Drawing

For an OEM quote, INCE needs the final part geometry and the exact parent-mesh requirement. A request for “100 micron plastic mesh discs” leaves the material grade, wire/thread diameter, tolerance, center hole, edge and support construction unresolved.

Nylon monofilament filter mesh for custom discs
Site-owned INCE nylon mesh image. Nylon discs are flexible; final suitability depends on the liquid and finished-part design.

How should buyers compare nylon and polyester discs?

Decision point Nylon mesh disc Polyester mesh disc
Mechanical character Flexible monofilament construction Dimensionally stable PET monofilament construction
Typical procurement reason Conforming insert, screen or flexible filter component Stable cut component, support or repeatable screening geometry
Critical evidence Polymer grade, aperture, thread diameter and wet-condition fit PET grade, aperture, thread diameter and dimensional tolerance
Edge options Raw cut, heat-sealed or drawing-defined edge where feasible Raw cut, heat-sealed or drawing-defined edge where feasible
Do not assume That “nylon” identifies chemical or temperature suitability That PET stability guarantees compatibility with every liquid

The INCE filter mesh disc page supports nylon, polyester, 304 stainless steel, 316L stainless steel and multilayer constructions. This article focuses on polymer discs so the commercial product page can remain the primary target for “filter mesh discs.”

Polyester monofilament filter mesh for custom discs
Site-owned INCE polyester mesh image. Confirm the exact PET parent mesh before cutting finished discs.

What drawing information prevents quotation revisions?

  • Finished outline: outside diameter, center-hole diameter, slots, flats or custom profile.
  • Tolerances: separate critical fit dimensions from noncritical cut dimensions.
  • Parent mesh: polymer, aperture, thread diameter, mesh count where used, weave and supplier designation.
  • Layer stack: single layer, fine mesh plus support, ring/washer stack or framed part.
  • Edge: raw cut, heat-sealed, welded, overmolded, framed or sample-matched.
  • Orientation: mark the filtration side if layers or weave directions differ.
  • Inspection: dimensional sampling, aperture evidence, cleanliness, visual defects and packaging.

Request OEM Disc Pricing

How should the process condition be written?

List every contacting liquid and concentration, normal and maximum temperature, expected differential pressure, cleaning chemical, cleaning temperature, service cycle and whether the part is discarded or reused. If the disc supports another media, state whether it is a filtration layer, support layer or spacer. A material name without this duty information is not a compatibility review.

For nozzle, valve or pump protection, also state the smallest downstream passage that must be protected and the particle shape expected. The mesh opening should be selected from the actual debris and equipment risk, not from a generic “fine/coarse” description.

Custom filter mesh fabrication for OEM disc production
Site-owned INCE fabrication image. Disc cutting, holes, layers and edge treatment should follow the approved drawing or sample.

First-article approval checklist

Check Acceptance record
Material Parent mesh identification and agreed polymer specification
Aperture Agreed inspection method and sampling plan
Geometry OD, ID, custom features and critical tolerances
Edge No unacceptable fraying, distortion or sharp projection for the assembly
Layering Correct order, alignment and joining method
Packaging Quantity per pack, flatness protection, label and lot reference

Frequently asked questions

Can a micron value be converted directly to mesh count?

Not reliably without the thread diameter and weave. Specify the actual opening or an approved parent-mesh code.

Can polymer disc edges be heat sealed?

Often, but feasibility and dimensional change must be confirmed for the selected mesh and part geometry.

What should an OEM buyer send?

Send the drawing, material, opening, OD, ID, layers, edge, liquid, temperature, pressure, cleaning method, quantity and destination.

Get a Mesh Disc Feasibility Review

Related Articles

Continue Reading About Liquid Filtration

Need a Filter Bag Recommendation?

Send the liquid, micron target, flow, pressure, temperature, bag dimensions and quantity for review.

Start a Filter Bag Inquiry
Filtration Engineer
● Online
×
WhatsApp