Direct answer: Match a melt-blown filter cartridge by the complete installed interface: nominal and actual length, outside and inside diameter, center core, open/closed end arrangement, adapter or fin, gasket profile and material, PP media, micron rating and service duty. INCE lists 10–60 inch lengths, 63 or 115 mm OD, 28 or 30 mm ID and multiple end options on the melt-blown filter cartridge product page. Similar appearance is not proof of drop-in compatibility.
Need a Melt-Blown Replacement Review?
Send the existing model and label, both-end photos, actual length/OD/ID, support-rod dimensions, end cap, gasket, micron, liquid, temperature, pressure, flow, quantity and destination.

Which Published Size Options Must Be Verified?
| Field | INCE published options | Buyer check |
|---|---|---|
| Length | 10, 20, 30, 40, 50 and 60 inch | Measure the installed overall length and sealing position |
| Outside diameter | 63 or 115 mm | Confirm basket/vessel clearance and element spacing |
| Inside diameter | 28 or 30 mm | Match the support rod, spring or mounting tube |
| Micron | 1, 3, 5, 10, 20, 30 and 60 µm | State rating basis and required evidence |
| Core | PP or stainless steel | Review strength, temperature and chemistry |
| Connection | Hot-melt-welded, no adhesive | Confirm the offered construction |
A 20-inch cartridge from one supplier may not share the same true installed length, gasket position or end geometry as another. Record the dimensions from sealing surface to sealing surface and include photographs with a ruler or dimensioned sketch.
Which End Caps and Seals Belong on the Drawing?
Published interface options include flat, 215, 222, high 222, 226, threaded, triangle tip, semi-winged tip and flat peak cover configurations. The same text name can still conceal differences in length, bayonet geometry, fin orientation or gasket groove, so the approved drawing or physical sample must control production.
| Component | RFQ information | Failure avoided |
|---|---|---|
| Open end | Port type, OD/ID, insertion depth and photos | Cartridge cannot seat or seal |
| Closed end | Flat, tip, fin or custom geometry | Incorrect support or orientation |
| Gasket | Profile, dimensions and silicone/EPDM/NBR/FKM option | Leakage, swelling or bypass |
| Center support | Core material, ID and required mechanical duty | Collapse or installation mismatch |

How Should Buyers Specify Media, Surface and Operating Duty?
INCE publishes a three-layer graded polypropylene melt-blown media construction and several surface appearances, including glossy, orange-peel, pressure-point, embossed, grooved and furry styles. Surface names are not interchangeable performance guarantees. Ask the supplier to state the offered media, surface, core, micron basis and available test evidence.
- Liquid composition, concentration and viscosity.
- Normal and maximum temperature and pressure.
- Normal and maximum flow per cartridge.
- Particle type, solids loading and required downstream protection.
- Clean differential pressure and plant change-out rule.
- Cleaning, hot-water or steam exposure, if any.
- Required cleanliness, declarations, lot records and packaging.
The product page lists 70°C and 2.0 bar differential pressure at 21°C as family references. These values do not authorize every end cap, core, gasket or liquid combination. The quotation must state the limit for the exact offered assembly.

Replacement Qualification and First Article
| Stage | Acceptance item |
|---|---|
| Identify | Original label, model, housing and installed quantity |
| Measure | Length, OD, ID, end caps, gasket and support interface |
| Specify | PP media, micron basis, surface, core and operating duty |
| Sample | Fit, seal, initial pressure drop and agreed process trial |
| Release | Approved drawing/code, label, packaging and revision |
Avoid a Size-Only Replacement Decision
Attach the existing cartridge, housing nameplate and dimensioned photos. INCE can identify open points and quote the exact construction offered without assuming equivalence.
Frequently Asked Questions
Are 63 mm and 115 mm melt-blown cartridges interchangeable?
No. They require different housing clearance and may use different supports and interfaces. Confirm OD, ID, length and both ends.
Is a 20-inch label enough to confirm fit?
No. Measure actual overall and sealing lengths, OD, ID, end caps and gasket because nominal length alone does not control the interface.
What information is needed for pricing?
Provide model/photos, length, OD, ID, end cap, seal, core, surface, micron, liquid, temperature, pressure, flow, quantity and destination.
Get Melt-Blown Cartridge Pricing
Send the complete replacement interface and process duty. The quotation should identify the proposed construction, deviations and sample-approval conditions.